| Common Name: | USA: ER80S-B2, ER90S-B3, ER80S-B6, ER80S-B8, ER90S-B9, ER100S-1, ER110S-1, 6000 |
| Manufacturer: | WELDING MATERIAL SALES |
| SDS Revision Date: | 4/28/2017 |
| SDS Format: | ANSI-OSHA |
| Item Number(s): | 225M09, 225M13, 225M66, 225M67, 225M68, 225M69, 225M70, 225N09, 225N10, 225N11, 225N12, 225N13, 225N14, 225N15, 225N16, 225N17, 225N18, 225N19, 225N20, 225N21, 225N22, 225N23, 225N24, 225N25, 225N28, 225N29, 225N32, 225N33, 225N34, 225N35, 225N36, 225N37, 225N90 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
SAFETY DATA SHEET
CHROMOLY/LOW ALLOY I
SDS #: 6000
REVISION DATE: 04/28/2017
WELDING MATERIAL SALES
SAFETY DATA SHEET (SDS)
FOR WELDING CONSUMABLES AND RELATED PRODUCTS CONFORMS TO OSHA HAZARD
COMMUNICATION STANDARD 29 CFR 1910.1200 STANDARD MUST BE CONSULTED FOR
SPECIFIC REQUIREMENTS
THE FOLLOWING INFORMATION AND RECOMMENDATIONS TO BEST OF OUR KNOWLEDGE
IS RELIABLE, HOWEVER DUE TO CONDITIONS OUTSIDE OUR CONTROL WE ASSUME NO
LIABILITY OR GUARANTEE WITH THE USE OF THIS INFORMATION. SAFETY DATA MAY
OR MAY NOT BE REQUIRED FROM OTHER SOURCE TO ENSURE ALL SAFETY GUIDELINES
ARE ACCEPTABLE FOR YOUR APPLICATION.
| SECTION I - IDENTIFICATION |  |
MANUFACTURER/SUPPLIER: WELDING MATERIAL SALES
ADDRESS:
1340 REED ROAD
GENEVA, IL 60134
TELEPHONE NO: 630-232-6421
EMERGENCY NO: 800-424-9300
E-MAIL: INFO@WELDINGMATERIALSALES.COM
TRADE NAME:
USA:
ER80S-B2, ER90S-B3, ER80S-B6, ER80S-B8, ER90S-B9, ER100S-1, ER110S-1,
ER120S-1, ER4130, BD140
TOOL STEELS: A-2, M-2, S-7, H-12, H-13, P-20
SPECIFICATION: AWS A5.28
AISI: NONE
| SECTION II - HAZARDOUS MATERIALS | |
IMPORTANT:
THIS SECTION COVERS THE MATERIALS FROM WHICH THE PRODUCT IS MANUFACTURED.
THE FUMES AND GASES PRODUCED DURING WELDING WITH THE NORMAL USE OF THIS
PRODUCT ARE COVERED UNDER SECTION V. THE TERM "HAZARDOUS MATERIALS" SHOULD
BE INTERPRETED AS A TERM REQUIRED AND DEFINED IN OSHA HAZARD OMMUNICATION
STANDARD 29 CFR 1910.1200 HOWEVER THE USE OF THIS TERM DOES NOT NECESSARILY
IMPLY THE EXISTENCE OF ANY HAZARD.
CHEMICAL COMPOSITION PERCENT BY WEIGHT:
NAME C Mn Si P S
70S-B2L(1) 0.05 0.40-0.70 0.40-0.70 0.025 0.025
80S-B2(1) 0.07-0.12 0.40-0.70 0.40-0.70 0.025 0.025
80SB3L(1) 0.05 0.40-0.70 0.40-0.70 0.025 0.025
80S-B6(1)(F) 0.10 0.40-0.70 0.50 0.025 0.025
80S-B8(1)(G) 0.10 0.40-0.70 0.50 0.025 0.025
80S-D2(2) 0.07-0.12 1.60-2.10 0.50-0.80 0.025 0.025
80S-G(2) 0.12 2.50 0.80 0.025 0.025
80S-Ni1(1)(V) 0.12 1.25 0.40-0.80 0.025 0.025
80S-Ni2(1) 0.12 1.25 0.40-0.80 0.025 0.025
80S-W 0.12 2.50 0.20-0.60 0.035 0.035
90S-B3 0.07-0.12 0.40-0.70 0.40-0.70 0.025 0.025
90S-B9(3) 0.07-0.13 1.20 0.15-0.50 0.010 0.010
100S-1(V)(4) 0.08 1.25-1.80 0.20-0.55 0.010 0.010
110S-1(V)(4) 0.09 1.40-1.80 0.20-0.55 0.010 0.010
120S-1(V)(4) 0.10 1.40-1.80 0.25-0.60 0.010 0.010
140S-1(V)(4) 0.15 2.50 0.80 0.010 0.010
4130, 4130VM 0.28-0.33 0.40-0.60 0.15-0.35 0.035 0.040
4140, 4140VM 0.38-0.43 0.75-1.00 0.15-0.35 0.035 0.040
4340, 4340VM 0.38-0.43 0.60-0.80 0.15-0.30 0.035 0.040
6130VM 0.28-0.33 0.60-0.90 0.15-0.35 0.008 0.008
6150 0.48-0.53 0.70-0.90 0.15-0.35 0.035 0.040
8620 0.18-0.23 0.70-0.90 0.15-0.35 0.035 0.040
9XX, 9XXX 1.6 1.5 1.8 V = 0.10-2.5
NAME Ni Cr Mo W
70S-B2L(1) 0.20 1.20-1.50 0.40-0.65
80S-B2(1) 0.20 1.20-1.50 0.40-0.65
80SB3L(1) 0.20 2.30-2.70 0.90-1.20
80S-B6(1)(F) 0.60 4.50-6.00 0.45-0.65
80S-B8(1)(G) 0.50 8.00-10.50 0.80-1.20
80S-D2(2) 0.15 0.40-0.60
80S-G(2) 0.50 2.50 1.25
80S-Ni1(1)(V) 0.80-1.10 0.15 0.35
80S-Ni2(1) 2.00-2.75
80S-W 0.50-2.80 0.30 1.40
90S-B3 0.20 2.30-2.70 0.90-1.20
90S-B9(3) 0.80 8.00-10.50 0.85-1.20
100S-1(V)(4) 1.40-2.10 0.30 0.25-0.55
110S-1(V)(4) 1.90-2.60 0.50 0.25-0.55
120S-1(V)(4) 2.00-2.80 0.60 0.30-0.65
140S-1(V)(4) 3.50 2.50 1.25
4130, 4130VM 0.25 0.80-1.10 0.15-0.25
4140, 4140VM 0.80-1.10 0.15-0.25
4340, 4340VM 1.65-2.00 0.70-0.90 0.20-0.30
6130VM 0.25 0.80-1.10 0.06
6150 0.80-1.10
8620 0.40-0.70 0.40-.060 0.15-0.25
9XX, 9XXX 0.20-2.0 0.20-6.00 0.15-10.0 7.50
(1)Cu <0.35
(2) Cu <0.50
(F) SIMILAR TO FORMER CLASS ER502
(G) SIMILAR TO FORMER CLASS ER505
(V) V <0.05
(4) Ti, Zr, Al <0.10 FOR EACH ELEMENT, Cu <0.25
(3) V=0.15-0.30, NIOBIUM (COLUMBIUM) 0.02-0.10, N 0.03-0.07
Fe = BALANCE; SINGLE VALES ARE MAXIMUM, EXCEPT WHERE NOTED
FLUX OR OTHER INGREDIENTS CAS NO. EXPOSURE LIMIT (MG/M3)
OSHA PEL ACGIH TLV
IRON (Fe) 7439-89-6 10 5
(LIMITS AS OXIDE FUME)
MANGANESE (Mn) 7439-96-5 1, 3.0**, 5* 2
(LIMITS AS FUME)(1)
SILICON (Si) 7440-21-3 15 (DUST), 10, 20**
5 (RESP)
COPPER (Cu)(1) 7440-50-8 1 (DUST), 1 (DUST),
0.1 (FUME) 0.2 (FUME)
MOLYBDENUM (Mo) 7439-98-7 15 10, 20**
NICKEL (Ni)(1) 7440-02-0 1 1, 1.5
(INHALABLE
FRACTION)
CHROMIUM (Cr)(C)(1) 7440-47-3 1 (METAL) 0.5 (METAL)
0.5 (Cr III) 0.5 (Cr III)
0.005 (Cr VI) 0.05 (Cr VI)
VANADIUM (V) RESPIRABLE 7440-62-2 0.05 AS V2O5 0.5 * AS V2O5
DUST(1)
TUNGSTEN 7440-33-7 5, 10 ** 5, 10 **
OTHER ELEMENTS OR INGREDIENTS MAY BE PRESENT BUT IN QUANTITIES MUCH LESS
THAN 1%. OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION 29 CFR 1910.1000
PERMISSIBLE EXPOSURE LIMIT (PEL). AMERICAN CONFERENCE OF GOVERNMENTAL
INDUSTRIAL HYGIENISTS (ACGIH) THRESHOLD LIMIT VALUE (TLV[R]).
(RESP) = RESPIRATORY/ RESPIRATION
*CEILING LIMIT
**SHORT TERM EXPOSURE LIMIT
(1) SUBJECT TO REPORTING REQUIREMENTS OF SECTION 302, 304, 311, 312, AND
313 OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF 1986 AND
40 CFR 370 AND 372
(C) TLV & PEL FOR WATER SOLUBLE Cr. III AND Cr. VI, WELDING AND CUTTING
OF PRODUCTS THAT CONTAIN CHROMIUM MAY PRODUCE HEXAVALENT CHROMIUM AND YOU
SHOULD READ AND FOLLOW OSHA'S FINAL RULES FED REGISTER #: 71:10099-10385
DATED 02-28-2006.
| SECTION III - PHYSICAL DATA | |
AS SHIPPED THESE ARE SOLID WIRE THAT ARE NONFLAMMABLE, NON-EXPLOSIVE,
NON-REACTIVE AND NON -HAZARDOUS -AND MAY BE COPPER COATED.
| SECTION IV - FIRE AND EXPLOSION HAZARD DATA | |
NON-FLAMMABLE:
WELDING ARC AND SPARKS CAN IGNITE COMBUSTIBLES. SEE Z-49.1 REFERENCED
IN SECTION VI.
| SECTION V - REACTIVITY & STABILITY DATA | |
HAZARDOUS DECOMPOSITION PRODUCTS:
WELDING FUMES AND GASES CANNOT BE CLASSIFIED SIMPLY. THE COMPOSITION AND
QUANTITY OF THESE FUMES AND GASES ARE DEPENDENT UPON THE METAL BEING
WELDED, THE PROCEDURES FOLLOWED AND THE ELECTRODES USED. WORKERS SHOULD BE
AWARE THAT THE COMPOSITION AND QUANTITY OF FUMES AND GASES TO WHICH THEY
MAY BE EXPOSED, ARE INFLUENCED BY: COATINGS WHICH MAY BE PRESENT ON THE
METAL BEING WELDED (SUCH AS PAINT, PLATING, OR GALVANIZING), THE NUMBER
OF WELDERS IN OPERATION AND THE VOLUME OF THE WORK AREA, THE QUALITY AND
AMOUNT OF VENTILATION, THE POSITION OF THE WELDER'S HEAD WITH RESPECT TO
THE FUME PLUME, AS WELL AS THE PRESENCE OF CONTAMINANTS IN THE ATMOSPHERE
(SUCH AS CHLORINATED HYDROCARBON VAPORS FROM CLEANING AND DEGREASING
PROCEDURE). WHEN THE ELECTRODE IS CONSUMED, THE FUMES AND GAS DECOMPOSITION
PRODUCTS GENERATED ARE DIFFERENT IN PERCENT AND FORM FROM THE INGREDIENTS
LISTED IN SECTION II, THE COMPOSITION OF THESE FUMES AND GASES ARE THE
CONCERNING MATTER AND NOT THE COMPOSITION OF THE ELECTRODE ITSELF.
DECOMPOSITION PRODUCTS INCLUDE THOSE ORIGINATING FROM THE VOLATILIZATION,
REACTION, OR OXIDATION OF THE INGREDIENTS SHOWN IN SECTION II, PLUS THOSE
FROM THE BASE METAL, COATING AND THE OTHER FACTORS NOTED ABOVE. REASONABLE
EXPECTED FUME CONSTITUENTS OF THIS PRODUCT WOULD INCLUDE:
COMPLEX OXIDES OF VANADIUM, TUNGSTEN IRON, MANGANESE, SILICON, CHROMIUM,
NICKEL, MOLYBDENUM AND COPPER. FUME LIMIT FOR Cr (VI) MAY BE REACHED BEFORE
LIMIT OF 5 MG/M3 FOR GENERAL WELDING FUMES IS REACHED. WATCH THE (Cr VI)
LEVEL. GASEOUS REACTION PRODUCTS MAY INCLUDE CARBON MONOXIDE AND CARBON
DIOXIDE OZONE AND NITROGEN OXIDES MAY BE FORMED BY THE RADIATION FROM THE
ARC. ONE METHOD OF DETERMINING THE COMPOSITION AND QUANTITY OF THE FUMES
AND GASES TO WHICH THE WORKERS ARE EXPOSED IS TO TAKE AN AIR SAMPLE FROM
INSIDE THE WELDER'S HELMET WHILE WORN OR WITHIN THE WORKER'S BREATHING
ZONE. SEE ANSI/AWS F1.1 PUBLICATION AVAILABLE FROM THE AMERICAN WELDING
SOCIETY 550 N.W. LEJEUNE ROAD, MIAMI, FLORIDA 33126.
STABILITY: AS SHIPPED THESE PRODUCTS ARE STABLE.
| SECTION VI - ENTRY DATA | |
COMMON ENTRY:
DURING THE WELDING PROCESSES INHALATION OF WELDING FUMES MAY GIVE THE
MOST COMMON ROUTE OF OVER EXPOSURE. CONTACT WITH SKIN, EYES, INGESTION
OR INJECTION SHOULD NOT BE A SOURCE FOR EXPOSURE WITH PROPER PROTECTION.
| SECTION VII - THRESHOLD LIMIT VALUE | |
THE ACGIH RECOMMENDED GENERAL LIMIT FOR WELDING FUME NOC (NOT OTHERWISE
CLASSIFIED) IS 5 MG/M3. ACGIH-1985 PREFACE STATES:
"THE TLC-TWA SHOULD BE USED AS GUIDES IN THE CONTROL OF HEALTH HAZARDS
AND SHOULD NOT BE USED AS FINE LINES BETWEEN SAFE AND DANGEROUS
CONCENTRATIONS." READ ALL OTHER SECTIONS FOR SPECIFIC FUME CONSTITUENTS,
WHICH MAY MODIFY THIS TLV.
| SECTION VIII - HEALTH HAZARD DATA | |
EFFECTS OF OVEREXPOSURE:
INHALATION OF WELDING FUMES AND GASES CAN BE DANGEROUS TO YOUR HEALTH.
SHORT-TERM (ACUTE) OVEREXPOSURE TO WELDING FUMES MAY RESULT IN DISCOMFORT
SUCH AS DIZZINESS, NAUSEA, OR DRYNESS OR IRRITATION OF NOSE, THROAT, OR
EYES. CHROMIUM (VI) COMPOUNDS PRESENT IN THE FUME MAY CAUSE ABDOMINAL PAIN,
DIARRHEA, MUSCULAR WEAKNESS AND CONVULSIONS. CONTINUED INHALATION COULD
CAUSE LOSS OF CONSCIOUSNESS AND DEATH. CHROMIUM (VI) COMPOUNDS PRESENT IN
THE FUME MAY CAUSE SEVERE IRRITATION OF THE BRONCHIAL TUBES AND LUNGS.
INGESTING CHROMIUM (VI) SALTS MAY CAUSE INJURY OF DEATH. CHROMIUM (VI)
COMPOUNDS MAY BURN EYES. CHROMIUM COMPOUNDS MAY CAUSE ALLERGIC REACTIONS
IN SOME PEOPLE. NICKEL OXIDES PRESENT IN THE FUME MAY CAUSE TIGHTNESS
AROUND THE CHEST, FEVER AND ALLERGIC REACTIONS IN SOME PEOPLE. LONG-TERM
(CHRONIC) OVER-EXPOSURE TO WELDING FUMES CAN LEAD TO SIDEROSIS (IRON
DEPOSITS IN LUNG) AND IS BELIEVED TO AFFECT PULMONARY FUNCTION. REPETITIVE
EXPOSURE TO FLUORIDE FUMES AND/OR GASES MAY CAUSE EXCESSIVE CALCIFICATION
OF THE BONES AND LIGAMENTS OF THE RIBS, PELVIS AND SPINAL COLUMN. CONSTANT
INHALATION OF CHROMIUM (VI) COMPOUNDS MAY CAUSE AN ULCERATION AND
PERFORATION OF THE NASAL SEPTUM AS WELL AS LIVER AND KIDNEY DAMAGE.
REPETITIVE OVEREXPOSURE TO NICKEL OXIDES MAY LEAD TO LUNG FIBROSIS OR
PNEUMOCONIOSIS. WORKERS EXPOSED TO CHROMIUM (VI) COMPOUNDS AND/OR NICKEL
OXIDES HAVE A HIGHER INCIDENCE OF LUNG AND NASAL CANCERS. CHROMIUM AND
NICKEL COMPOUNDS ARE ON THE IARC (INTERNATIONAL AGENCY FOR RESEARCH OF
CANCER) LIST AS POSING A CARCINOGENIC RISK TO HUMANS.
ARC RAYS CAN INJURE EYES AND BURN SKIN. ELECTRIC SHOCK CAN KILL. SEE
SECTION VII. CARCINOGENICITY & CALIFORNIA PROPOSITION 65 LISTED IN
SECTION X
| SECTION IX - EMERGENCY AND FIRST AID PROCEDURES | |
REMOVE TO FRESH AIR. CALL FOR MEDICAL ASSISTANCE. USE FIRST AID PROCEDURES
RECOMMENDED BY THE AMERICAN RED CROSS. IF BREATHING IS DIFFICULT OR NOT
BREATHING - GIVE OXYGEN OR USE CPR (CARDIOPULMONARY RESUSCITATION) BY
TRAINED PERSONNEL. CONSULT A PHYSICIAN IF IRRITATION OF THE EYES AND SKIN
OR FLASH BURNS DEVELOPS AFTER EXPOSURE.
| SECTION X - TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
OVEREXPOSURE OR INHALATION OF LARGE AMOUNTS OF WELDING FUMES MAY CAUSE
SYMPTOMS SUCH AS METAL FUME FEVER, DIZZINESS, NAUSEA, DRYNESS AND
IRRITATION OF YOUR NOSE, THROAT OR EYES AS WELL AS OTHER LUNG DISEASE.
CHRONIC TOXICITY:
OVEREXPOSURE OR PROLONGED INHALATION OF LARGE AMOUNTS OF WELDING FUMES
WITH CHROMIUM COMPOUNDS MAY CAUSE CANCER. OTHER OVEREXPOSURE OR PROLONGED
INHALATION OF LARGE AMOUNTS OF WELDING FUMES SYMPTOMS RELATED MAY INCLUDE
DAMAGE TO THE CENTRAL NERVOUS SYSTEM, RESPIRATORY SYSTEM, SKIN AND COULD
AFFECT ORGANS SUCH AS PANCREAS AND LIVER
CARCINOGENICITY:
OSHA (29 CFR 1910.1200) LISTS NICKEL AND CHROMIUM AS POSSIBLE CARCINOGENS.
CALIFORNIA PROPOSITION 65:
THESE PRODUCTS MAY CONTAIN OR PRODUCES CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, AND/OR BIRTH DEFECTS (OR OTHER REPRODUCTIVE
HARM). (HEALTH AND SAFETY CODE SECTION 25249.5 ET SEQ.)
| SECTION XI - SAFE HANDLING AND STORAGE | |
HANDLING:
DO NOT EAT OR DRINK WHILE USING THESE PRODUCTS AND ENSURE PROPER
VENTILATION IS USED.
STORAGE:
STORE IN A COOL DRY PLACE AWAY. AVOID EXTREME TEMPERATURES AND INCOMPATIBLE
ITEMS SUCH AS ACIDS, OXIDIZERS AND HALOGENS.
| SECTION XII - DISPOSAL & WASTE | |
WASTE DISPOSAL METHOD:
RECYCLE WHEN POSSIBLE. DISCARD ANY UN-WANTED PRODUCT, RESIDUES, CONTAINERS,
OR LINERS IN A SUITABLE DISPOSAL CONTAINER IN AN ENVIRONMENTALLY ACCEPTABLE
MANNER APPROVED BY FEDERAL, STATE AND LOCAL REGULATIONS
| SECTION XIII - CONTROL MEASURES AND PERSONAL PROTECTION | |
READ AND UNDERSTAND THE MANUFACTURER'S INSTRUCTIONS AND PRECAUTIONARY
LABEL ON THIS PRODUCT AND YOUR EMPLOYER'S SAFETY PRACTICES. SEE AMERICAN
NATIONAL STANDARD ANSI Z49.1 SAFETY IN WELDING, CUTTING AND ALLIED
PROCESSES, PUBLISHED BY THE AMERICAN WELDING SOCIETY, 550 N.W. LEJEUNE
ROAD, MIAMI, FLORIDA 33126; OSHA SAFETY AND HEALTH STANDARDS ARE PUBLISHED
BY THE U.S. GOVERNMENT PRINTING OFFICE, 732 NORTH CAPITOL STREET NW,
WASHINGTON, DC 20401 FOR MORE DETAILS ON THE FOLLOWING TOPICS.
VENTILATION:
USE PLENTY OF VENTILATION AND/OR LOCAL EXHAUST AT THE ARC, TO KEEP THE
FUMES AND GASES BELOW THE THRESHOLD LIMIT VALUE WITHIN THE WORKER'S
BREATHING ZONE AND THE GENERAL WORK AREA. WELDERS SHOULD BE ADVISED TO
KEEP THEIR HEAD OUT OF THE FUMES.
RESPIRATORY PROTECTION:
USE RESPIRABLE FUME RESPIRATOR OR AIR SUPPLIED RESPIRATOR WHEN WELDING
IN A CONFINED SPACE OR GENERAL WORK AREA WHERE LOCAL EXHAUST AND/OR
VENTILATION DOES NOT KEEP EXPOSURE BELOW THE THRESHOLD LIMIT VALUE.
EYE PROTECTION:
WEAR A HELMET OR FACE SHIELD WITH A FILTER LENS SHADE NUMBER 12-14 OR
DARKER. SHIELD OTHER WORKERS BY PROVIDING SCREENS AND FLASH GOGGLES.
PROTECTIVE CLOTHING:
WEAR APPROVED HEAD, HAND AND BODY PROTECTION, WHICH HELP TO PREVENT INJURY
FROM RADIATION, SPARKS AND ELECTRICAL SHOCK. SEE ANSI Z-49.1. THIS WOULD
INCLUDE WEARING WELDER'S GLOVES AND A PROTECTIVE FACE SHIELD AND MAY
INCLUDE ARM PROTECTORS, APRON, HATS, SHOULDER PROTECTION, AS WELL AS DARK
SUBSTANTIAL CLOTHING. WELDERS SHOULD BE TRAINED NOT TO ALLOW ELECTRICALLY
LIVE PARTS TO CONTRACT THE SKIN OR WET CLOTHING AND GLOVES. THE WELDERS
SHOULD INSULATE THEMSELVES FROM THE WORK AND GROUND.
| SECTION XIV - OTHER INFORMATION | |
NFPA CODES:
FIRE 0
HEALTH 2
REACTIVITY 0
WELDING MATERIAL SALES INC. BELIEVES THAT THE INFORMATION CONTAINED
IN THIS (SDS) SAFETY DATA SHEET IS ACCURATE. HOWEVER, WELDING MATERIAL
SALES INC. DOES NOT EXPRESS OR IMPLIES ANY WARRANTY WITH RESPECT TO THIS
INFORMATION.